You are Unregistered, please register to be able to read posts in all forums and participate in the discussion.
Results 1 to 10 of 10

Thread: Trykon Tunning

  1. #1
    Junior Member
    Join Date
    May 2008
    Posts
    3

    Default Trykon Tunning

    Hi there
    I am new here
    reason is ..that i like some help whit my paper tuning.
    I love 3d shooting .
    so i am seting up my Trykon for it
    Problem is the tuning,
    I am susing a 50-60pound 29 1/2 draw Trykon
    and carbon express 3d sellect maxima 250/300 spine
    But what ever i try ?? left tear 45 degrees 3 inches long
    I'ts driving me nuts ,
    I must be doing someting wrong

    Can some one please give me some tips

  2. #2
    Bisquit....... BowhuntnHoosier's Avatar
    Join Date
    Jan 2006
    Location
    Hoosierville
    Posts
    13,882

    Default

    to the forum. Sorry but I don't put much faith into paper tuning. But I am sure if you give it time someone will come along and help ya out. HCAman has a Trykon maybe he will show up and help out.

    Again I would like to say WELCOME and hope you enjoy yourself here.


    "HONDA"

  3. #3
    Senior Member
    Join Date
    Feb 2008
    Location
    McArthur, Ohio
    Posts
    836

    Default

    what kind of a release are you using?

  4. #4
    Slippy for President Hook Em's Avatar
    Join Date
    Jul 2007
    Location
    At Home in Texas
    Posts
    1,938

    Default

    Welcome to the site! Not trying to discourage you, but the only way I could paper tune my Trykon was to move my rest as far as it would go to the left....of course you wouldn't want to shoot it like that. Just set the center shot the best you can and walk back tune. Paper tune schmaper tune!
    Hook 'Em Horns

  5. #5
    ONE SHOT ONE KILL TEN RING's Avatar
    Join Date
    Feb 2008
    Location
    western pa
    Posts
    380

    Default

    you may have some flecthing interferance

  6. #6
    Junior Member
    Join Date
    May 2008
    Posts
    3

    Default

    Quote Originally Posted by archer1983 View Post
    what kind of a release are you using?
    Hey

    I am shooting with a carter holething release,and a D loop .

  7. #7
    Senior Member tnts79's Avatar
    Join Date
    Jul 2007
    Location
    Illinois
    Posts
    1,014

    Default ?

    x2 Sounds like fletching contact.
    Hoyt Trykon-390 gr.@280fps.
    Truglo Tool-less / 5-.019" pins
    WB/Double STS/S-Coil Stab./CSS Tunerz
    5575 GT XT Hunters/G5 Tekan-II/Tru-Ball Copperhead

  8. #8
    Senior Member
    Join Date
    Jan 2008
    Location
    Buckley, Michigan
    Posts
    671

    Default

    I shoot an ultra mag. at 60# with a 29" draw. I had the same problem when I went from CX 300 shafts to terminator LT. 4560's. The chart showed that they were within specs., but I had to adjust my rest way out to get a decent tear in the paper. I switched to terminator LT. select 6075 shafts and the problem went away. If you're stuck on the more expensive maxima's, try the 350 shaft's. If not, the terminatoer Lt. selects are made to the same straightness and weight differance standards as the maxima, and only cost me 70.00 a doz.

  9. #9
    Junior Member
    Join Date
    May 2008
    Posts
    3

    Default

    Quote Originally Posted by J.Blay View Post
    I shoot an ultra mag. at 60# with a 29" draw. I had the same problem when I went from CX 300 shafts to terminator LT. 4560's. The chart showed that they were within specs., but I had to adjust my rest way out to get a decent tear in the paper. I switched to terminator LT. select 6075 shafts and the problem went away. If you're stuck on the more expensive maxima's, try the 350 shaft's. If not, the terminatoer Lt. selects are made to the same straightness and weight differance standards as the maxima, and only cost me 70.00 a doz.

    Hi

    yes i also read on archery talk that some one used ultra stif arrow's and a foc 7/9 %
    Ill try the 350 Maxima ,and see what that brings
    thanks for the responce.

  10. #10
    Senior Member tnts79's Avatar
    Join Date
    Jul 2007
    Location
    Illinois
    Posts
    1,014

    Default

    I shoot 5575 gold tip xt's at 65 lbs. and a 29" draw 100 gr. head, and mine punches bullet holes??
    Hoyt Trykon-390 gr.@280fps.
    Truglo Tool-less / 5-.019" pins
    WB/Double STS/S-Coil Stab./CSS Tunerz
    5575 GT XT Hunters/G5 Tekan-II/Tru-Ball Copperhead

Similar Threads

  1. Question about Tunning a Bow
    By Cloverwolf in forum Beginners Archery Range
    Replies: 2
    Last Post: 09-19-2008, 11:19 PM
  2. BH tunning.....
    By IChim2 in forum General Archery Forum
    Replies: 5
    Last Post: 01-05-2008, 03:36 PM
  3. Broad head tunning
    By Colo_Lee in forum Beginners Archery Range
    Replies: 2
    Last Post: 09-24-2007, 07:50 PM
  4. tunning issue
    By jkg3117 in forum General Archery Forum
    Replies: 15
    Last Post: 09-15-2007, 09:25 PM
  5. Bow Tunning
    By MO.HICK in forum General Archery Forum
    Replies: 7
    Last Post: 06-04-2007, 08:04 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •