You are Unregistered, please register to be able to read posts in all forums and participate in the discussion.
Results 1 to 11 of 11
  1. #1
    Junior Member
    Join Date
    Jan 2008
    Posts
    17

    Default need help timming rest

    I have a tt shake hunter on a Z7 .I marked the fletching & seen it was hitting plus it ripped off the felt on the left side of the prongs.iam shooting 2vanes down ,ive tried turning the nock ,tried raising the nock point .it was tied in at the bottom of the roller guard serving .I got it tied in at the the bottom of the handle . right now .the rest still comes up about half way thru the draw . so How do i set it up so it come the last inch of the draw ?

  2. #2
    Senior Member TMax27's Avatar
    Join Date
    Sep 2008
    Location
    Fairland, OK
    Posts
    778

    Default

    Mad, you need to tie pull down cable in about the bottom of the grip. However it sounds as if you need to lengthen the cable. The cable should have enough slack in it that it comes up the last 1/2" of draw.


    Here's an easy way to tie in a cable.
    http://www.3dshoots.com/forums/showthread.php?t=19402
    2008 Elite XXL 29 3/4" 70lbs- G1 Camo
    2008.5 Elite XLR 29 3/4" 60lbs- Ninja
    2009 Elite XLR 29 3/4" 65lbs- Metallic Red
    2009 Elite GT500 w/ Cuda Cams 25" 47lbs- Pink Ninja

  3. #3
    Senior Member TMax27's Avatar
    Join Date
    Sep 2008
    Location
    Fairland, OK
    Posts
    778

    Default Check it out

    http://www.trophytaker.com/inserts/a...est_adjust.htm

    This has the basic instructions. I use the "dloop" style of installation instead of the "through the cable" installation.
    2008 Elite XXL 29 3/4" 70lbs- G1 Camo
    2008.5 Elite XLR 29 3/4" 60lbs- Ninja
    2009 Elite XLR 29 3/4" 65lbs- Metallic Red
    2009 Elite GT500 w/ Cuda Cams 25" 47lbs- Pink Ninja

  4. #4
    Junior Member
    Join Date
    Jan 2008
    Posts
    17

    Default

    thanks I do like that dloop Ill be doing that it looks alot easier instead of pressing it everytime .

    I have tied in the bottom I give it more slack get in the way of the cables .how much slack should I give it at the bottom of the handle ?

  5. #5
    Senior Member TMax27's Avatar
    Join Date
    Sep 2008
    Location
    Fairland, OK
    Posts
    778

    Default

    You just have to have enough slack to have the rest come up last 1/2" of draw. I'll try to find you a picture... brb

    Look in this thread by DB. It shows it clearly.
    http://www.3dshoots.com/forums/showthread.php?t=29676
    2008 Elite XXL 29 3/4" 70lbs- G1 Camo
    2008.5 Elite XLR 29 3/4" 60lbs- Ninja
    2009 Elite XLR 29 3/4" 65lbs- Metallic Red
    2009 Elite GT500 w/ Cuda Cams 25" 47lbs- Pink Ninja

  6. #6
    Junior Member
    Join Date
    Jan 2008
    Posts
    17

    Default

    Quote Originally Posted by TMax27 View Post
    You just have to have enough slack to have the rest come up last 1/2" of draw. I'll try to find you a picture... brb

    Look in this thread by DB. It shows it clearly.
    http://www.3dshoots.com/forums/showthread.php?t=29676
    I got the timming marked its no longer hitting .thank you !Now i got another problem ,how do you keep it from sliding up .I used end thru the loo p know about an inch long & its sliding up with b 50 do you think #4 will hold it better

  7. #7
    Senior Member TMax27's Avatar
    Join Date
    Sep 2008
    Location
    Fairland, OK
    Posts
    778

    Default

    You can use serving material or what I use, BCY Nock Point Thread.

    Use a series of overhand knots, finishing w/ a square knot. Keep each knot very tight.
    2008 Elite XXL 29 3/4" 70lbs- G1 Camo
    2008.5 Elite XLR 29 3/4" 60lbs- Ninja
    2009 Elite XLR 29 3/4" 65lbs- Metallic Red
    2009 Elite GT500 w/ Cuda Cams 25" 47lbs- Pink Ninja

  8. #8
    Junior Member
    Join Date
    Jan 2008
    Posts
    17

    Default

    Quote Originally Posted by TMax27 View Post
    You can use serving material or what I use, BCY Nock Point Thread.

    Use a series of overhand knots, finishing w/ a square knot. Keep each knot very tight.
    ok thank you

  9. #9
    Senior Member TMax27's Avatar
    Join Date
    Sep 2008
    Location
    Fairland, OK
    Posts
    778

    Default

    No problem
    2008 Elite XXL 29 3/4" 70lbs- G1 Camo
    2008.5 Elite XLR 29 3/4" 60lbs- Ninja
    2009 Elite XLR 29 3/4" 65lbs- Metallic Red
    2009 Elite GT500 w/ Cuda Cams 25" 47lbs- Pink Ninja

  10. #10
    Junior Member hutchies's Avatar
    Join Date
    Jan 2007
    Location
    Durant, OK
    Posts
    402

    Default

    I don't know about the last 1/2 inch of draw though. I try to tie mine to come up the last 3 inches of your draw cycle. That way if you have a tendency to creep the arm wont drop.

  11. #11
    Senior Member TMax27's Avatar
    Join Date
    Sep 2008
    Location
    Fairland, OK
    Posts
    778

    Default

    Think you are correct Hutchies. Went and looked at my wife's bow, last 1 1/2". Loooked at the TT website, they say last 1 to 2 1/2".

    Sorry for the mis-info
    2008 Elite XXL 29 3/4" 70lbs- G1 Camo
    2008.5 Elite XLR 29 3/4" 60lbs- Ninja
    2009 Elite XLR 29 3/4" 65lbs- Metallic Red
    2009 Elite GT500 w/ Cuda Cams 25" 47lbs- Pink Ninja

Similar Threads

  1. FS or Trade: Octane Hostage Pro rest and Whisker Biscuit rest!!
    By VtecGSR95 in forum Sights, Scopes and Rests
    Replies: 1
    Last Post: 09-28-2009, 09:22 AM
  2. rest
    By Robbie81 in forum General Archery Forum
    Replies: 0
    Last Post: 02-09-2009, 06:48 PM
  3. QAD Ultra-Rest HD Pro Series-GOOD rest?
    By Kevin2 in forum Bowhunting forum
    Replies: 6
    Last Post: 12-29-2008, 09:48 AM
  4. QAD rest
    By tornacl in forum General Archery Forum
    Replies: 2
    Last Post: 10-19-2008, 09:04 PM
  5. Kaz-Away Rest
    By Chops in forum Archery Equipment Accessories - Buy Sell Trade
    Replies: 1
    Last Post: 08-23-2006, 08:05 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •