You are Unregistered, please register to be able to read posts in all forums and participate in the discussion.
Results 1 to 8 of 8
  1. #1
    Member ES21's Avatar
    Join Date
    Jul 2009
    Location
    Kinmundy, IL
    Posts
    79

    Default Spot shooters: X jammer 27 help please

    Set up is contender elite, 26 3/4 draw, 45 lbs. I have my x jammers at full length 33" and a 210 grain point. I'm getting a consistent left tear unless I move the rest in towards the riser. That will get rid of the tear but I would like to have the rest more center.

    Tuning charts say to stiffen arrow but i don't always agree. A lot of times in the past I found a under spine arrow worked better. Anyways, I'm asking any one who has experience w/ these shafts, would you add to the point weight to make them less stiff or would u cut them down to stiffen them?

    On another note, these long arrows w/ the heavy point are a pain in the butt to keep on the arrow rest while drawing the bow. Any ideas on this? I know it is not nock pinch because the other arrows I try work just fine. Just a pain. The rest is a hoyt lizard tounge with the .010 blade.

    Thanks in advance

  2. #2
    Senior Member Archerdad's Avatar
    Join Date
    Aug 2007
    Location
    Oklahoma
    Posts
    896

    Default

    according to ontarget2 software your arrows are way too stiff. no need to stiffen them anymore.
    is that rest the v shape launcher blade? those are hard to keep any arrow on in my experience.

    i doubt you would ever get them to soften up enough at that draw weight and draw length to make a difference.
    i would dump shooting through paper and see how they group, and work towards the best groupings. you can add bigger fletchings to help control the arrow more also. which may also improve your groups.

    you would have to shoot 300 grains up front and be shooting 60 pounds to get them close to being weak enough to get a correct spine and at that they are still stiff.

  3. #3
    Member ES21's Avatar
    Join Date
    Jul 2009
    Location
    Kinmundy, IL
    Posts
    79

    Default

    Thank you for the info.. I have heard of people shooting 300 plus grains up front. I'll give that a try. If I can soften them up any at all it will be better.

    I have 4 inch feathers on now and the grouping was better after I tuned but you can still tell they just are not flying like they should. With the rest closer to center they were all over the place.

    Also, it is the v launcher blade but the other arrows I use pull back great on it. Just the x jammers fall right off. Thanks again for your help.

  4. #4

  5. #5
    Senior Member
    Join Date
    Nov 2008
    Posts
    183

    Default

    I didn't have much of a problem tuning my xj 27's. I moved my rest very little off of center. I'm shooting a hoyt cam 1/2+, 50#'s, 28 1/2" draw, arrows cut 30 ", 220 grain tips. I'm using the original trophy taker drop rest. Shoots prefect bullet holes. They make wide v lanchers, try that.
    Hoyt Bows, Shrewd sights, Carter index, Tru Ball hinge, Trophy Taker Rest, Doinker Stabilizers, Carbon Express XJ 27's, Vapor Trail Strings, Nikon Binos.

  6. #6
    Senior Member Brown Hornet's Avatar
    Join Date
    Jan 2008
    Location
    Hornet's Nest
    Posts
    511

    Default

    Carbon does not act like aluminum.....DO NOT put that much point weight in those shafts. I wouldn't even leave them full length.

    I am fortunate enough to shoot with Braden Gellenthien who is the # 1 ranked archer in the world....he NOW shoots for CX so we get to do some testing. He is shooting that shaft and what is working for him right now is a 30" shaft with 210 up front....he is shooting more lbs then you and has a little more draw weight....but it doesn't matter. Which setup we shoot them from they pound. I still think they would work shorter though....and would work better. I have a buddy that has about a 26" draw and his are cut to about 26" and they POUND for him also.

    If your center shot is WAY off...you may want to tune to another arrow 1st to get things lined up.....

  7. #7
    Member
    Join Date
    Jan 2008
    Location
    Wisconsin, USA
    Posts
    870

    Default

    I tend to have to agree with this, for the most part when shooting carbon the arrow length is ĹĒ past the rest and the average tip weight for indoor setups is 120 to 200 grains. That said you will see that the majority shooting the GT triples run 150 up front.

    I would start out by getting your center shot on your rest back to where it should be and then if anything try cutting down one of your arrows and back your tip weight down and shoot it and see how consistent it is at hitting the same hole at a distance that your capable of shooting well even if itís 15 yards try a few there check your arrows repetitiveness or consistency and then move back. Some folks get all worked up about how a given setup is shooting at 20 or beyond but in many cases itís the operator not the setup.

    Once you know your arrows are shooting well and to the point of being forgiving then build the others to match and go into the game with confidence. Remember itís only 20 yards and when shooting outdoors this is known to be your easy gemmy shot. Keep that in mind and donít put any unneeded pressure on the game

    Good Luck
    The only one that is your competitor is the air between your ears!



  8. #8
    Member ES21's Avatar
    Join Date
    Jul 2009
    Location
    Kinmundy, IL
    Posts
    79

    Default

    Thank you all for the advice. Let the playing around begin!

Similar Threads

  1. Line jammer Arrows...
    By kgoss33@gmail.com in forum General Archery Forum
    Replies: 0
    Last Post: 03-12-2010, 05:14 PM
  2. Line jammer 350 size
    By Holy Smokes in forum General Archery Forum
    Replies: 0
    Last Post: 01-09-2009, 05:55 PM
  3. Hey Spot shooters-need help?
    By beenfarr in forum General Archery Forum
    Replies: 17
    Last Post: 08-20-2007, 06:11 AM
  4. Jammer points
    By Holy Smokes in forum General Archery Forum
    Replies: 3
    Last Post: 08-12-2007, 07:37 PM
  5. X-Jammer
    By ovation21 in forum General Archery Forum
    Replies: 0
    Last Post: 12-09-2005, 08:42 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •