Archery Forums 3DShoots.com
Find Archery Shoots near you  |   Advertise on 3DShoots.com

Go Back   Archery Forums 3DShoots.com > Archery Forum > Bowhunting forum
 

Reply
 
Thread Tools Display Modes
Old 07-21-2005, 10:38 AM   #1
glenny
Senior Member
 
Join Date: Jun 2004
Location: N.Illinios
Posts: 309
glenny is on a distinguished road
Send a message via MSN to glenny
Default Epoxy recomendations for inserts.

Anyone find any epoxy that is the bomb for precisely tuning broadheads and holding up in the cold conditions?
I had some great plains stuff before and it worked alright....
Any suggestions?
glenny is offline   Reply With Quote
Old 07-25-2005, 09:54 AM   #2
docsatterfield
Junior Member
 
Join Date: Jul 2005
Location: Warminster, PA
Posts: 5
docsatterfield is on a distinguished road
Default Glue recommendations

I have been using Cyber 007, made by R.S. Archery Products, inc. for 2 years to set all bushing, points, inserts. 60-80 dozen arrows yearly. rarely does this glue fail in any condition. it is not an epoxy, so there is no mixing.
docsatterfield is offline   Reply With Quote
Old 07-25-2005, 02:11 PM   #3
glenny
Senior Member
 
Join Date: Jun 2004
Location: N.Illinios
Posts: 309
glenny is on a distinguished road
Send a message via MSN to glenny
Default Cyber 007

Where can I purchase this product?
Can I get a web address.
Maybe I will give it a whirl,
What is the setting time to work with?
glenny is offline   Reply With Quote
Old 07-25-2005, 10:01 PM   #4
docsatterfield
Junior Member
 
Join Date: Jul 2005
Location: Warminster, PA
Posts: 5
docsatterfield is on a distinguished road
Default cyber 007

www.rsbowvise.com/archery_products.htm is the web site. your local pro shop should be able to order it for you. if not the site list several folks you get purchase it from. i order mine from kinsey's wholesale.

unlike goat tough where you only have 3 to 5 seconds this product gives you between 20-30 seconds and after 5 minutes you are ready to shoot.
docsatterfield is offline   Reply With Quote
Old 07-26-2005, 02:53 PM   #5
glenny
Senior Member
 
Join Date: Jun 2004
Location: N.Illinios
Posts: 309
glenny is on a distinguished road
Send a message via MSN to glenny
Default Is 30 seconds enough time?

I use the G5 straitening(squaring) device on the shaft and then put my insert in and square that up.When I securely screw in the broadhead to the insert or 0 ring.I then spin the arrow to see how it is true.
Usually,ever since I have used the squaring device this method works 9 times out of ten.
If it don't, I guess I can just try and put a different broadhead in,or O-ring and see if it spins true then.
I was thinking of just getting some slower epoxy to spin the broadhead and insert on the shaft.
I wonder how to square up the insert without it being on the shaft before you glue it in?
Hot Melt it and use a marker to line it up again maybe?
glenny is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 01:17 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Copyright 2004 3DShoots.com