Archery Forums 3DShoots.com
Find Archery Shoots near you  |   Advertise on 3DShoots.com

Go Back   Archery Forums 3DShoots.com > Archery Forum > General Archery Forum
 

Reply
 
Thread Tools Display Modes
Old 07-14-2004, 10:50 AM   #1
bow-regard
Member
 
Join Date: Jun 2004
Posts: 34
bow-regard is on a distinguished road
Default Question String Loops

Ok, I have seen many loop styles. Both knots below, one above, one below, etc.

I prefer the one above and one below the nock. But, do I tie serving knots above and below the loop knots to keep them from sliding together and pinching the nock of the arrow?
bow-regard is offline   Reply With Quote
Old 07-14-2004, 02:56 PM   #2
OutbackRuss
Junior Member
 
Join Date: Jul 2004
Location: Salisbury NC
Posts: 25
OutbackRuss is on a distinguished road
Send a message via AIM to OutbackRuss
Default

thats what i have done
__________________
Here's my setup Mathews Outback, Alpine Soft-Loc 5 arrow Quiver, Impact Solo-site, NAP Quicktune 2000 RG Arrow rest, Vibracheck stabilizer, Sims Ultra Limb Savers, Scott Mongoose NCS Release. Shooting Easton Axis Arrows (400's)


"The beast is dead, Long live the beast!"
OutbackRuss is offline   Reply With Quote
Old 10-05-2004, 07:55 PM   #3
archery480
Junior Member
 
Join Date: Oct 2004
Location: Jamestown, IN
Posts: 9
archery480 is on a distinguished road
Default

It does help the loop from pinching the nock
archery480 is offline   Reply With Quote
Old 10-05-2004, 09:37 PM   #4
glenny
Senior Member
 
Join Date: Jun 2004
Location: N.Illinios
Posts: 309
glenny is on a distinguished road
Send a message via MSN to glenny
Default Depends what kind of bow and release you got

I learned alot from a couple of guys on loops,I would recomend if it's a single cam to go with both ends below the nock and serve above the nock.
If it's a cam1/2,at the nocking point serving goes below the nock(the same size as your release throat)loop under that and then on top of nock.What this does is line the nock up perfectly with the end of your release.You can use serve anchor or small serving on top,if you choose to,but,I feel this is a good one.
I always have them opposite of each other one tied one way the other the other,preferably if you use a release that turns or twists the loop, in that direction.
Usually all the tention on the loop is upward and serving is placed above,serving below is unnessesary.
I have done cushions with small serving above and below my nock,and then the loop with more cushion serving above and below the loop,reassuring that that nock was in placement everytime,but found it was overkill,it did work though,just depends how much you want to untie if you change your knocking point.
If you choose to do these methods it will greatly increase your groups and if you aren't sure how,pm me.

Last edited by glenny; 10-05-2004 at 09:41 PM.
glenny is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:37 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Copyright 2004 3DShoots.com