Who Has A Drenalin? I need serving lengths!!

Discussion in 'General Archery Forum' started by jcmorgan31, Mar 12, 2008.

  1. jcmorgan31

    jcmorgan31 Prodigal Son

    4,569
    4
    0
    If you have one and are willing to help, here is what I need.

    Follow the string down from the nock point to the post it is hooked to and measure from the end of that end loop to get the following measurements.

    1. end loop to end of that end serving.
    2. end loop to start of center serving; length of center serving
    3. end loop to start of idler serving; length of idler serving
    4. end loop to start of roller guard serving; length of roller guard serving
    5. length of other end serving from its end loop.

    Cable

    1. length of end serving opposite the split.
    2. end loop to start of roller guard serving and the length of the roller guard serving.

    thanks in advance to whoever has the time to help me out... :thumb:
     
  2. BUNNYMAN

    BUNNYMAN I pray for you!

    29,903
    12
    0

    i am guessing a Dren LD is different:laugh: :laugh:
     

  3. Ronhop

    Ronhop RIP

    3,967
    1
    0
    I'd love to help you JC but I don;t know anybody who has one... :noidea:

    Ron
     
  4. jcmorgan31

    jcmorgan31 Prodigal Son

    4,569
    4
    0
    You are wise beyond your years.......:peace:
     
  5. BUNNYMAN

    BUNNYMAN I pray for you!

    29,903
    12
    0
    wise guy beyond my years.....

    I am going to the shop later this morning, if you dont have your info by then I will get it for you........
     
  6. jcmorgan31

    jcmorgan31 Prodigal Son

    4,569
    4
    0
    Sounds good.
     
  7. BUNNYMAN

    BUNNYMAN I pray for you!

    29,903
    12
    0
    I have your info, you want it here or, in a PM??:biggrin1:
     
  8. jcmorgan31

    jcmorgan31 Prodigal Son

    4,569
    4
    0
    Sure...... :laugh: :laugh:
     
  9. BUNNYMAN

    BUNNYMAN I pray for you!

    29,903
    12
    0
    Partial PM sent.......
     
  10. BUNNYMAN

    BUNNYMAN I pray for you!

    29,903
    12
    0
    hello Justin, are you there???
     
  11. BUNNYMAN

    BUNNYMAN I pray for you!

    29,903
    12
    0
    where did you go buddy, I sent you some info.......hello:noidea:
     
  12. BowhuntnHoosier

    BowhuntnHoosier Bisquit.......

    13,887
    15
    0
    I think he left the building................:peace:
     
  13. BUNNYMAN

    BUNNYMAN I pray for you!

    29,903
    12
    0
    maybe the brain left ITS buiding:noidea:
     
  14. tedicast

    tedicast Member

    328
    0
    0
    I have a set of factory Dren strings sitting in front of me, if you need any info. :peace:
     
  15. jcmorgan31

    jcmorgan31 Prodigal Son

    4,569
    4
    0

    Got what I need my friend. Thanks... :thumb:
     
  16. jcmorgan31

    jcmorgan31 Prodigal Son

    4,569
    4
    0
    Unless your string has a gap between the roller guard serving and the idler serving. :noidea:
     
  17. BUNNYMAN

    BUNNYMAN I pray for you!

    29,903
    12
    0
    I took a brand new set of strings and cables out of the package and measured them:noidea: :noidea:
     
  18. jcmorgan31

    jcmorgan31 Prodigal Son

    4,569
    4
    0
    10-4. I wasn't sure if Mathews did their factory strings that way too or not. I know winner's choice does.

    It will work. Just a lot of wasted serving......:wave:
     
  19. tedicast

    tedicast Member

    328
    0
    0
    Both my Vapor Trails, and factory strings have no gap.